Sale!

Emerson 1C31142G01 Vortex Flowmeter

Brand: EMERSON

Model number:1C31142G01

Colour:new                                    Warranty: 12 months

Lead Time:3-day working day   Country of origin: USA

Price: Please contact us         Product weight:0.3kg

Category: SKU: 1C31142G01 Brand:

Description

Emerson 1C31142G01 Vortex Flowmeter

Emerson offers its industrial vortex flowmeters under the Rosemount™ 8800 and Rosemount™ 8600 series, designed for measuring liquids, gases, and steam.

 

Product Overview

  • Operating Principle: Uses the Von Kármán vortex street effect. As fluid flows past a non-streamlined bluff body (shedder bar), it creates alternating swirling vortices at a frequency directly proportional to flow velocity.
  • Sensor Architecture: A mass-balanced piezoelectric sensor behind the shedder bar detects pressure pulses from the vortices without contacting the process fluid.
  • Body Styles: Available in Flanged, Wafer (flangeless), Reducer (built-in reduced bore for low flows), Weld-End, and Threaded-End configurations.

 

Technical Parameters

  • Volumetric Accuracy:
    • Liquids: ±0.65% of flow rate
    • Gases & Steam: ±1.0% of flow rate
    • MultiVariable Mass Flow (Steam): ±1.2% to ±2.5% depending on pressure and compensation mode
  • Turndown Ratio: Up to 38:1 (Rosemount 8800) or 30:1 (Rosemount 8600)
  • Process Temperature Range:
    • Rosemount 8800: -200 °C to +427 °C (-330 °F to +800 °F)
    • Rosemount 8600: -50 °C to +250 °C (-58 °F to +482 °F)
  • Line Sizes:
    • Rosemount 8800: DN15 to DN350 (1/2 in. to 14 in., depending on style)
    • Rosemount 8600: DN25 to DN200 (1 in. to 8 in.)
  • Pressure Ratings: ASME Class 150 to 1500, DIN PN10 to PN160, JIS 10K to 40K
  • Wetted Materials: 316/316L & CF3M stainless steel, Nickel Alloy C-22/CW2M, carbon steel (A105/WCB, LF2/LCC), and Duplex stainless steel
  • Output Signals: 4–20 mA with HART 5 or 7, scalable pulse output (0–10,000 Hz), FOUNDATION Fieldbus, or Modbus RS-485
  • Power Supply: 10.8 to 42 VDC (16.8 VDC minimum required for HART communication)

 

Key Advantages

  • Zero Leak Points & Non-Clog Body: The all-cast, gasket-free Rosemount 8800 body removes internal ports and impulse lines that typically clog or leak.
  • Online Sensor Replacement: Both flow and temperature sensors sit isolated from the process fluid, allowing technicians to swap them without shutting down or depressurizing the pipe.
  • High Vibration Immunity: Mass-balanced sensors paired with Adaptive Digital Signal Processing (ADSP) filter out pipe vibration and low-flow noise.
  • Built-In Diagnostics & Verification: An internal signal generator lets technicians verify electronics without removing the meter, while Smart Fluid Diagnostics detect liquid-to-gas phase changes.
  • Lower Installed Cost with Reducer & MultiVariable Models: Integral reducer bodies eliminate field-welded pipe reducers, and built-in temperature sensors remove the need for separate thermowells.

 

Installation & Usage Precautions

  • Straight-Pipe Run Requirements: Leave sufficient straight unobstructed pipe upstream (typically 10–35 pipe diameters depending on elbows or valves) and downstream (5 pipe diameters) to avoid swirl and flow profile distortion.
  • Gasket Protrusion: Ensure flange gaskets align with the pipe’s inner diameter—gaskets extending into the bore disturb vortex shedding and cause measurement errors.
  • Minimum Reynolds Number: Vortex meters need turbulent flow (typically Re > 10,000 for linear accuracy). Avoid high-viscosity fluids or ultra-low flow velocities where vortices stop shedding cleanly.
  • Control Valve Placement: Always install control valves downstream of the vortex flowmeter so valve throttling or flashing does not disrupt incoming flow.
  • Two-Phase & Dirty Slurry Limits: Designed for clean, single-phase liquids, gases, and steam. Heavy solids, fibrous slurries, or wet gas slugs can coat the shedder bar or trigger false counts.
  • High-Temperature Electronics Orientation: When measuring hot steam above 200 °C, mount the transmitter housing to the side or bottom of a horizontal pipe (or use remote-mount electronics) so rising heat doesn’t overheat the circuit board.

 

Applications

  • Steam & Boiler Systems: Saturated and superheated steam mass flow monitoring, boiler efficiency tracking, and plant energy allocation.
  • Chemical & Petrochemical Processing: Corrosive solvents, hydrocarbon gases, nitrogen blanketing, and clean-in-place (CIP) blowdown detection.
  • Power Generation & Utilities: Compressed air, chilled/cooling water, natural gas headers, and condensate return lines.
  • Safety Instrumented Systems (SIS): High-integrity flow interlocks (up to SIL 3) using the Dual or Quad Rosemount 8800 configurations.

 

Verdict

Choose the Rosemount 8800 Series for critical process lines, extreme temperatures (-200 °C to +427 °C), or steam mass-flow compensation. Choose the Rosemount 8600 Series when you need a simpler meter for clean utility water, air, or general steam headers.

Shipping Port: Xiamen, China

Payment: Bank of Chicago, Bank of Singapore

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Please make an inquiry for more models:

Emerson 12P0678X022
Emerson 12P0678X032
Emerson 12P0681X072
Emerson 12P0683X082
Emerson 12P1064X072
Emerson 12P1064X08R
Emerson 12P1064X122
Emerson 12P1442X042
Emerson 12P1509X052
Emerson 12P1731X082
Emerson 12P1732X042
Emerson 12P1732X062
Emerson 12P2186X012
Emerson 12P2471X042
Emerson 12P2506X062
Emerson 12P2536X042
Emerson 12P3162X162
Emerson 12P3935X032
Emerson 12P4986X
Emerson 13A0054G04
Emerson 13A0066G01
Emerson 13A0066G02
Emerson 13A0066G04
Emerson 13A0068G02
Emerson 13A0069G01
Emerson 13A0070H17
Emerson 13A0072G01
Emerson 13A0073G08
Emerson 13A0076G01
Emerson 13D0092G01